Electric Scooter Forum for Scooter Enthusiasts, Scooter Chargers, and Scooter Mechanics.

Covers electric scooter models whether shared or for consumers.
#12571
ZipperZ wrote:
Mon Jul 08, 2019 2:42 am

Also maybe someone who has removed the gray potting material could share the model of MCU? @fieldc0llapse maybe? Was trying to connect through "programming" connector using ST-LINK/V2, but no luck, maybe the programming through SWD is disabled? (I am sure that it is read protected, but I may have something to try)
Did not have the patience while was waiting for the 1st post to be approved. If someone needs the controller is: MKE02Z64VLD4

To view images REGISTER or LOGIN for full access.


To view images REGISTER or LOGIN for full access.
Last edited by ZipperZ on Sun Aug 11, 2019 5:00 pm, edited 1 time in total.


#12599
Have a question.

I have two scooters. One with a display that does not display anything (but I can connect via bluetooth and use the segway app, change the colors of the led etc.) to the other the display turns on and then goes out.
I did the following, I changed the handlebars between them and I can connect every time through the bluetooth and control the speed lamp etc.
As a solution, I bought (and am waiting) for a full handlebars in there. Because I'm looking for the information on the display.

The questions would be:

1 - I will be able to use the handlebar display right?
2 - My central card is not locked, right?


Sorry, I'm anxious, that's why the questions are soooo much lost!


#12639
Hello,I found dumped in a garbage container Ninibot KickScooter ES1.I pressed the power-on display and, to my surprise, was working,but does not start nor does Bluetooth connection.just by turning the front wheel sounds beep beep.tell me what I need to change so I can use it-motherboard, display and can I remove bluetooth connection too,and just to go without the need a bluetooth connection!


#12863
Hi, i just order same control unit. Can i ask you for some wiring diagram ? Wich wires connect together. And can i use original throttle pro not? Thanx a lot. Tomas
carbacca wrote:
Sat Dec 15, 2018 7:28 pm
images here - excuse the camouflage. am also waiting for another enclosure box to tidy it up a bit


the two parts i used - box and wiring instructions all chinese - beware if you dont read chinese....

https://www.aliexpress.com/item/Finger- ... 1a2eyCz3Pd

https://www.aliexpress.com/item/36V-48V ... 8f12Gi1fLm

#12928
no because i didnt write anything down. i didnt use the original throttle so i have no idea what the pin outs are like

you can figure it out quite easily by elimination and intelligent guessing
Hellrider87 wrote:
Mon Jul 15, 2019 4:08 pm
Hi, i just order same control unit. Can i ask you for some wiring diagram ? Wich wires connect together. And can i use original throttle pro not? Thanx a lot. Tomas
carbacca wrote:
Sat Dec 15, 2018 7:28 pm
images here - excuse the camouflage. am also waiting for another enclosure box to tidy it up a bit


the two parts i used - box and wiring instructions all chinese - beware if you dont read chinese....

https://www.aliexpress.com/item/Finger- ... 1a2eyCz3Pd

https://www.aliexpress.com/item/36V-48V ... 8f12Gi1fLm



  • 1
  • 93
  • 94
  • 95
  • 96
  • 97
  • 107

i wired the bleu on the thin red i turn switch o[…]

I've updated both BMS to version 1.4.1, but I st[…]

Haha got this working New Zealand 10/10 tell […]

Which two cables did you bridge? I'm guessing yo[…]