An Electric Scooter Community on a Mission to Stamp out Transportation Mediocrity.

Covers electric scooter models whether shared or for consumers.
#17669
WayneB wrote:
Tue Nov 19, 2019 5:31 pm
Hi all, new user here from NZ.
To view images REGISTER or LOGIN for full access.

To view images REGISTER or LOGIN for full access.

This is what the inside of the green box looks like here...
[https://usermanual.wiki/MeiG-Smart-Tech ... LM750/info] is the link for the download for the SLM750 module, although it doesn't appear to tell you much. I'm still playing around with it, and am grateful for any help, assistance and advice from my fellow posters.
I just wanna get this bitch to run...
The sim card installed in this case appears to be of Chinese origin... dunno how it works here in New Zealand unless its roaming?
This looks like the same model I have, the SJ 2.5. Info I have so far:
  • Just power and serial lines - Kernel Panic
  • Power then Ground for 2 seconds - Additional Boot still Kernel Panic
  • Power then Ground for 5 seconds - DEBUG but still Kernel Panic
To view images REGISTER or LOGIN for full access.

https://i.imgur.com/rC0f2d8.png
i.imgur.com/rC0f2d8.png

I don't have the SIM (decommissioned unit) but from research they should be:
https://www.twilio.com/
www.twilio.com

The SLM750 actually runs a full Linux OS, they're somewhat available publicly. But the specific software for programming them does not appear to be.



#17890
ZipperZ wrote:
Wed Nov 13, 2019 1:55 am
wurecec wrote:
Sun Nov 10, 2019 9:56 pm
Chuchin wrote:
Sun Sep 15, 2019 6:13 am



Hello, i have a full boot.
https://pastebin.com/bG110UCt
Could you share how you managed to get a full boot?
As far as I know there are two ways:
1. As written in service manual with magnet, but then you have to have a working SIM, which would mean you have a stolen (not decomissioned) scooter.
2. Other way is to enter "Debug" mode, which is enabled when certain "load" is present on UART lines. I cant remember which one, but either CH340 or CP2102 adapter was recognized as a debug probe.
Option 2 ... My scooter is bought - out of service.
You do not need a SIM card to fully load modem. I used the DEBUG port with the CH340 converter, that's all.
Now I'm rebuilt with another controller.


#18078
it does not matter I answer myself. To view images REGISTER or LOGIN for full access.


there is a guy who found a solution without changing bms controller
I think we can use an ardurino as a GPS emulator he put 2 videos To view images REGISTER or LOGIN for full access.


I give you the link To view images REGISTER or LOGIN for full access.


viewtopic.php?f=56&t=5767&p=18077#p18077

#18141
I found this battery at the street\garbage, i dont have any electric scooter so i just plan to use the cells for other projects. Do you know if the cells on this type of batteries are high drain ones?

I openit and sadly they put a lot of some silicon everywhere.. covering everything. I will try to remove all of it to unpack the cells from the plastic box.

To view images REGISTER or LOGIN for full access.

To view images REGISTER or LOGIN for full access.

To view images REGISTER or LOGIN for full access.

To view images REGISTER or LOGIN for full access.


The BMS board have one LED flashing, first of all, i am thinking cut the niquel straips (-), (+) , (B1-B9)..

#18300
Hello everyone,
I have LIME-S scooter. and now i need to get it working. Is it possible to operate with the original control unit? Or do I need to buy a new control unit? I read all pages (120) but I dont choose right solution. PLEASE for HELP.

Im good mechanic but not gut IT with flash.



Thank YOU

By Fmbf
Posts
#18405
Hi im looking for a photo, schematic or someone to explain how i can use the controller for ebike project without the comm.Box or dash display. BASICALLY turn it on.
To view images REGISTER or LOGIN for full access.

User avatar
By Sc00tr
Posts LikeBB LikeBB Avatar
#18416
This isn’t super helpful for us to give us information that might help you... what are you using for the bike? What motor? What battery?

You would get better results by posting a new thread in the ninebot forum.
Fmbf wrote:
Tue Dec 24, 2019 9:18 pm
Hi im looking for a photo, schematic or someone to explain how i can use the controller for ebike project without the comm.Box or dash display. BASICALLY turn it on.
To view images REGISTER or LOGIN for full access.

  • 1
  • 118
  • 119
  • 120
  • 121
  • 122
  • 131
Lime gen 3

i gotcha. dm me. oklahoma

Tier ES400 unlock development

[...] 2) I cant get over 24kmh... Is there somet[…]

It has its own connection on the esc, not conne[…]

@Teslaguy hey can you inbox me. I had a questio[…]