An Electric Scooter Community on a Mission to Stamp out Transportation Mediocrity.

Enjoy the juice
#19400
Hello,

To find out if its possible to flash this Version of the lime gen 3 you have to disassemble one of the scooters and look inside. If the motor controller looks the same as the lime gen 3 we can try it. Would be interest in seeing whats inside this new Lime scooter. From where do you come? Where have you seen this scooter?



#19678
Hi there
I flashed the lime 3.0 successfully, it worked immediately after writing the hex file,
, headlights came on, the green light and the taillight.
Great, but another question how can you turn it off now (that the lamps go out until next time (how do you turn it on again)
after a short while he asks DONE? may I confirm that ???
MFG from Germany Berlin

#19693
Hello

Actually theres no way to disable the lights without flashing a locked firmware version to the scooter. The "Done" message should be disappear if you shake the scooter a little bit, it is in a normal case to ask the driver if he is done with renting.

#19696
Ventomann wrote:
Thu Feb 13, 2020 6:39 pm
Hi there
I flashed the lime 3.0 successfully, it worked immediately after writing the hex file,
, headlights came on, the green light and the taillight.
Great, but another question how can you turn it off now (that the lamps go out until next time (how do you turn it on again)
after a short while he asks DONE? may I confirm that ???
MFG from Germany Berlin
To view images REGISTER or LOGIN for full access.

I wired up a simple toggle switch on the headlight wire. Cut off the black sheath and wire the switch up to interrupt either the black or the white wire

#19698
Hi, I've tried using the ST st-link V2 with stlink.git from texanne,

So finally, with stlink-gui & stink.git & all dependencies installed & the right connections between stlinkV2 and controller , I've managed to upload the .hex file.
Light is on, charger at poste, no green box.
Let's try it now.
Last edited by jonsmit on Tue Feb 18, 2020 6:22 am, edited 2 times in total.


#19732
jonsmit wrote:
Sat Feb 15, 2020 5:11 pm
Hi, I've tried using the ST st-link V2 with stlink.git from texanne,

So finally, with stlink-gui & stink.git & all dependencies installed & the right connections between stlinkV2 and controller , I've managed to upload the .hex file.
Light is on, charger at poste, no green box.
Let's try it now.
Well, without reconnecting the green box or the lcd, and pushing the scoot to start nothing much happened. Light went down shortly after.

#19733
jonsmit wrote:
Tue Feb 18, 2020 6:33 am
jonsmit wrote:
Sat Feb 15, 2020 5:11 pm
Hi, I've tried using the ST st-link V2 with stlink.git from texanne,

So finally, with stlink-gui & stink.git & all dependencies installed & the right connections between stlinkV2 and controller , I've managed to upload the .hex file.
Light is on, charger at poste, no green box.
Let's try it now.
Well, without reconnecting the green box or the lcd, and pushing the scoot to start nothing much happened. Light went down shortly after.
Battery full after some serious tlc, reconnecting the green box:
All lights on, check.
Lcd green "asking are you done", km/h ok, check.
Bluetooth BLE ok asking for code through android phone, check.
No detection through eTrick app.
pushing up to 4-5 km/h into appartment no start...

disconnecting front light rear light on for some time, then scooter off.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 8
how can i unlock a bird zero?

I have 4 bird zero es100 scooters that im tr[…]

Tier ES400 unlock development

Guys, I'd like to swap the electric motor for a 48[…]

Seagull Unlock/Diagnostic tool

I purchased a Seagull tool to unloack a bird elect[…]

So the majority of the people here are about perso[…]