An Electric Scooter Community on a Mission to Stamp out Transportation Mediocrity.

Covers electric scooter models whether shared or for consumers.
#18794
There are some photos of internal controler wires pinout description - it seems like we can reprograming this controller by J-tag!
Q:
1. it's possible to write any SOFTWARE from original Nineboot, or sth?
2. Where to find that SOFTWARE?
3. One of plug seems like typical controller connection, but we haven't standard VCC, GND, TX, DT, as is Nineboot/Xiaomi.

GREEN PLUG - I was trying to put HI-digit (5V) at tx/rx pin to start controller, but is not so easy To view images REGISTER or LOGIN for full access.
Anyone have alive Like to test what signal at TX/RX give permission to start controller?
To view images REGISTER or LOGIN for full access.

#18949
Hi and thank all who posted the construction.
Scooter works great ...

Control unit $ 6
gas $ 7
voltage converter 36-4,3V for $ 4
spray black $ 5
$ 5 charger
a few hours of work ....

Cut out some material ...
Use original small connectors for lights ...
Everything is stored in the handlebar as originally.
Stop light will work if I buy a switch lever ... unnecessary ... for now ..

Remove the new control unit from the aluminum housing and screw it on the handlebar body inside for cooling.
The control unit does not fit into the handlebars completely - to cut out some material.
Connect the main motor cable directly to the control unit - without connector.

Thank you all.
Good ride ....
John


To view images REGISTER or LOGIN for full access.

To view images REGISTER or LOGIN for full access.

To view images REGISTER or LOGIN for full access.

To view images REGISTER or LOGIN for full access.

To view images REGISTER or LOGIN for full access.

To view images REGISTER or LOGIN for full access.

To view images REGISTER or LOGIN for full access.


#19045
Alex2425 wrote:
Tue Jun 11, 2019 4:16 am
I am not lazy but if you find the way how to do it i don t understand why you din t pin it. Here are 87 pages and everybody as the same question and nobady says exaclty how to do it.
FirstJuicerInTown wrote:
Mon Jun 10, 2019 4:59 pm
Man, just read this thread, everything is in here.
I’m so full of you sluggards, just coming here and asking for solutions that we’ve been working out for weeks. And even now when everything is already solved since a long time, you are still too lazy to look for it first, just asking for it to be served for you on a plate. Every few posts there is someone. This is main reason im not active there anymore.
Yes they do and almost all answers are there! How would you know unless you actually went through all pages??? like for real, how do you remove the green box on a lime? If people cant figure this one out on their own then there is NO way that they are going to know how to do anything else not less update firmware or flashing!! Seriously dont waste your time
Edmund liked this

#19046
Bot1029384756 wrote:
Mon Aug 12, 2019 5:44 pm
How can I remove the SIM card in order to deactivate the GPS? To view images REGISTER or LOGIN for full access.
OMG if you cant figure out how to remove the sim card ( which doesnt even need to be removed since you have ZERO need for the GPS anyways) then you arent going to be able to figure any of the actual DIFFICULT stuff that is involved! Stop wasting peoples time or do some research on your own first! I read this entire thread all 122 pages of it and half of that time was wasted on reading questions that were answered already dozens of times!!!! So Fucking Annoying!!!
Edmund liked this

#19048
ninebot wrote:
Wed Sep 04, 2019 6:16 am
Hey I am sorry i dont have time to read a thousand posts in this thread already is there any way to kickstart the thing (lime es2) with only the 5 pin prong jutting out? (I have the gps board)

I tried shorting some pins nothing as of yet please help To view images REGISTER or LOGIN for full access.
Hey buddy! Heres what I would do in your situation... First you need to pull your hand out of your pants, it might be a little hard for you but you can do it! Then you need to put it right up in front of your face. Then, take the 3rd finger over from your pinky finger and stick that finger straight up! Then last but not least, fold all your other fingers down and thats my suggestion to you, since you don't have the time to read all the posts like the rest of us! Why the hell should we take the time to help your lazy ass? Sorry thats not the way life works! Get off your ass and put in some work for yourself
stehno731, Edmund, Nissan liked this

#19214
Mike mike wrote:
Sat Aug 24, 2019 9:31 pm
Hi Guys, so I bought a 350w generic controller and fitted it. Scooter was working just fine:

To view images REGISTER or LOGIN for full access.



I designed an enclosure for all components and start printing on my Ender 5 3D Printer:

To view images REGISTER or LOGIN for full access.

To view images REGISTER or LOGIN for full access.

To view images REGISTER or LOGIN for full access.
Can you share the 3d box model please?

  • 1
  • 118
  • 119
  • 120
  • 121
  • 122
Tier ES400 unlock development

As a side note, those of you interested in learnin[…]

Suspense is killing me

Hi all ^^ I tried to get the ES200 unlock code fr[…]

It's impressive how much bang for the buck you get[…]