Electric Scooter Forum for Scooter Enthusiasts, Scooter Chargers, and Scooter Mechanics.

Covers electric scooter models whether shared or for consumers.

By samzone
Posts LikeBB
#12723
Bentobox wrote:
Thu Jul 11, 2019 12:38 am
THANK YOU SAMZONE, XD To view images REGISTER or LOGIN for full access.
:twistsed:. Any idea for get folding pole????????
i waiting for the ninebot max to come to the streets because the neck pipe looks similar i think is oval not round like the bird one so maybe we can buy that folding mechanism but thats all i have found so far go take alook to that ninebot max look good

By samzone
Posts LikeBB
#12725
SiameseMoms wrote:
Thu Jul 11, 2019 1:00 am
jaysonjehsen wrote:
Thu Jul 11, 2019 12:10 am
@SiameseMoms, if you follow Samzone's instructions, you'll be pretty set. Other things you'll need to have in general to do this are: Once you get a donor scooter, unscrew the torx screws underneath the top sticker/decal in the console between the handlebars. locate and unscrew the GPS/cellular dashboard. remove/destroy the SIM card in the board. Unplug the wire harness connection between that board and the cable that runs down through a black epoxy'd hole to the neck tube of the scooter. It should be like 10-12 wires in a bundle. Unplug the Li-Po battery on the board. you can toss that board away and recycle the Li-Po battery (it's pretty big capacity-- use it in a later project!). Then, unplug the cables with special orange/blue male/female connections and save those for soldering later-- as shown in samzone's video. That's all you'll need to prep the top of the scooter. Save all the screws and try to remember where they all came from so you can close everything back together at the end.

For the bottom of the scooter, there are around 10 torx security screws on the bottom lip that runs around the deck of the scooter, oriented to screw up (the heads to unscrew are facing down). Unscrew all of those, being careful to also unscrew the ones near the kickstand. Then carefully lift the deck up off the bottom of the scooter, and disconnect the orange connection cable to the brake light. Then, you have full access to the bottom of the scooter to replace the motor controller. At that point, you'll be at where samzone's video begins, and you'll need to do the soldering/connecting to the proper places as samzone shows so elegantly in his video.

If i missed anything @samzone let us know!
i am not aware of what soldering you are talking about, i dont see anywhere in the video, just him splicing wires together, also i am wondering if you still need to "flash" the board or do any software related things to make it fully functional.
thanks for the reply
you did better than me if someone is not able to do this with all this information we supply i dont know how they will good luck
jaysonjehsen, Sc00tr liked this

By jaysonjehsen
Posts LikeBB
#12727
samzone wrote:
Thu Jul 11, 2019 3:03 pm
jaysonjehsen wrote:
Wed Jul 10, 2019 10:57 pm
How'd you learn to use the universal controller? Is there a manual or instructions when it comes to electric bike/scooter motor controllers? I'd like to learn myself sometime!
there is a manual that help you alittle but most of the way i use a little of reading searching and a little of common sense and i did it i going to make a video today to show how to program the controller kit
You're the boss @samzone. Big fan.




By samzone
Posts LikeBB
#12742
To view images REGISTER or LOGIN for full access.
i think with this potetiometer i can make the light work and also put a little bit more of power just a bit enough to make then bright little bit more when i finish i will post the result i have a bunch of option for this but i will try the cheap one first

By SiameseMoms
Posts
#12743
I just want to make sure I am completely understanding this, i have never done electrical work before, and i have never modified something like a scooter, that is why i am asking these questions.

If i have this same model of scooter, the only thing i have to do is change the controller as sam shows in the video and it will be working 100% ???

I do not have to replace any other pieces or do any software updates or "flashing" correct?

By absolutejdm
Posts
#12745
SiameseMoms wrote:
Thu Jul 11, 2019 8:27 pm
I just want to make sure I am completely understanding this, i have never done electrical work before, and i have never modified something like a scooter, that is why i am asking these questions.

If i have this same model of scooter, the only thing i have to do is change the controller as sam shows in the video and it will be working 100% ???

I do not have to replace any other pieces or do any software updates or "flashing" correct?
CORRECT!

  • 1
  • 5
  • 6
  • 7
  • 8
  • 9
  • 19
[ES2] Error 18 and ground issues

Salut Sur les ninebots l'erreur 18 correspond &ag[…]

BIRD ZERO ELECTISAN F350

Buenas tengo un bird one y le e puesto el contro[…]

Clone? M365 Scooter Help

So I attempted my first upgrade. I bought a Pro D[…]

what company is it?