By feijocas - Wed Aug 28, 2019 12:04 am
- Wed Aug 28, 2019 12:04 am
#14716
Bought one from ebay, very cheap, 50 dollars.
Perfect scooter (best handling, firm on the ground, nice speed,neat battery capacity,etc).
This a Tutorial on how to make your lime-S scooter the Best in the block scooter (>40km/h scooter..)
How to change it to an EVEN BETTER scooter:
1) Get the scooter:
2) take out the garbage: Scooter controller, display,etc:
3) Buy a 350watt scooter motor controller with display controller: 40 dollars:
https://www.banggood.com/36V-48V-350W-B ... rehouse=CN
4) Cut of the original cables from the original controller because they are going to be used in the Hall sensor cable to the motor.
6) Use the following schematic and connect all the wires from the motor, original scooter throttle button, lights,etc.
The only cables to use are:
-3 Motor phase wires
-5 wires from the hall sensor from the motor
- Positive and negative wires from the battery (use the original connector from the original controller to connect it to the battery)
- Display connection --> directly to the display connection
-Accelerator --> connect to the original throttle switch on the handlebar.
PS: for the lights, the controller has 36V output but lights are 4.5Volt therefore you need a stepdown converter 36V to 4.5Volts (very cheap 3 dollars on aliexpress).
7) buy a box which can handle all the wires,cables,etc (3 dollar box):
I have cut the inner side of the box and rounded it so that it fits nicely over the fork handle. See the pictures to know what I mean.
8) Alter the controller so that it enables maximum speed:
Change the internal shunt in the PCB inside (you will find it in EVERY motor controller)) and put it a much thicker one.
This will bypass the speed limit and power to the scooter to enable max speeds of up to 40km/h (25mph)...
9)Enclosure all the cables, controller inside the box and .. voilá..
Here you have the finest and most powerful scooter on the market:
10) Program the Display Parameters on your scooter motor controller as this:
Press "+" and "-" button for 3 seconds to enter parameter settings:
Choose:
P1=2 (brightness level of the display)
P2=0 (km/h) or =1 (mph)
P3=36V (battery voltage)
P4=0 (sleep time=0)~
P5=0 (NO Power assist mode)
P6=8 (8 inch wheels)
P7=30 (normal number of magnets)
P8=100 (max speed)
P9=0 (Zero start)
P10=1 (NO pedal assist, or maximum power on start)
P11=24 (Boost sensivity)
P12=5 (max boost strength)
P13=5 (Magnetic steel disc type)
P14=20 (max amps to motor)
P15=29 (minimum voltage allowed)
P16= used to clear odometer recordings (reset kilometers made)
P17=0 (NO cruise control)
P18=100 (100% display speed)
P19=1 (No gear enabled)
P20=0 (Protocol Nº2)
Now on the Display use "+" button to set the Throttle (THL) to 2 or 3, 3 his high speed 45km/h!!..
The Scooter is So fast it is difficult to believe..
Faster than any scooter I have ride on
Here you have
Have a nice scooter!!.
Perfect scooter (best handling, firm on the ground, nice speed,neat battery capacity,etc).
This a Tutorial on how to make your lime-S scooter the Best in the block scooter (>40km/h scooter..)
How to change it to an EVEN BETTER scooter:
1) Get the scooter:
2) take out the garbage: Scooter controller, display,etc:
3) Buy a 350watt scooter motor controller with display controller: 40 dollars:
https://www.banggood.com/36V-48V-350W-B ... rehouse=CN
4) Cut of the original cables from the original controller because they are going to be used in the Hall sensor cable to the motor.
6) Use the following schematic and connect all the wires from the motor, original scooter throttle button, lights,etc.
The only cables to use are:
-3 Motor phase wires
-5 wires from the hall sensor from the motor
- Positive and negative wires from the battery (use the original connector from the original controller to connect it to the battery)
- Display connection --> directly to the display connection
-Accelerator --> connect to the original throttle switch on the handlebar.
PS: for the lights, the controller has 36V output but lights are 4.5Volt therefore you need a stepdown converter 36V to 4.5Volts (very cheap 3 dollars on aliexpress).
7) buy a box which can handle all the wires,cables,etc (3 dollar box):
I have cut the inner side of the box and rounded it so that it fits nicely over the fork handle. See the pictures to know what I mean.
8) Alter the controller so that it enables maximum speed:
Change the internal shunt in the PCB inside (you will find it in EVERY motor controller)) and put it a much thicker one.
This will bypass the speed limit and power to the scooter to enable max speeds of up to 40km/h (25mph)...
9)Enclosure all the cables, controller inside the box and .. voilá..
Here you have the finest and most powerful scooter on the market:
10) Program the Display Parameters on your scooter motor controller as this:
Press "+" and "-" button for 3 seconds to enter parameter settings:
Choose:
P1=2 (brightness level of the display)
P2=0 (km/h) or =1 (mph)
P3=36V (battery voltage)
P4=0 (sleep time=0)~
P5=0 (NO Power assist mode)
P6=8 (8 inch wheels)
P7=30 (normal number of magnets)
P8=100 (max speed)
P9=0 (Zero start)
P10=1 (NO pedal assist, or maximum power on start)
P11=24 (Boost sensivity)
P12=5 (max boost strength)
P13=5 (Magnetic steel disc type)
P14=20 (max amps to motor)
P15=29 (minimum voltage allowed)
P16= used to clear odometer recordings (reset kilometers made)
P17=0 (NO cruise control)
P18=100 (100% display speed)
P19=1 (No gear enabled)
P20=0 (Protocol Nº2)
Now on the Display use "+" button to set the Throttle (THL) to 2 or 3, 3 his high speed 45km/h!!..
The Scooter is So fast it is difficult to believe..
Faster than any scooter I have ride on
Here you have
Have a nice scooter!!.
Last edited by feijocas on Thu Aug 29, 2019 10:54 pm, edited 2 times in total.