An Electric Scooter Community on a Mission to Stamp out Transportation Mediocrity.

Covers electric scooter models whether shared or for consumers.
By ciol
Posts
#18930
thanks for the answer,

i've tried to connect the self learning cable, the motor go the correct way, but with cruise controll around 10 km/H

i haven't connected the HALL sensor, so i will update my post when the hall sensor will be connected, it might help !

thanks



Merci pour la réponse !

j'ai essayé en branchant directement les 2 cables verts, le moteur va dans le bon sens, mais va a 10km/h en cruise controll, sans action de l'accélérateur...
bref j'ai fait tous ces tests sans les capteurs Hall connecté, je pense que je vais arreter de jouer a l'apprenti sorcier, et brancher les cables HALL avant de continuer

Merci encore

By ciol
Posts
#18971
So, for futures users :

how to use the self study wire :

connect all cable to the motor, with matching colors, including hall sensor,
and connect the remote.

connect the 2 wire of the self study, power on the controller, carefull the motor will spin in a auto cruise mode. let it go for severals seconds, disconnect the self study cable, and, voila ! it's done.

i've got the error code 00, witch is... no error...
this is the error codes :
https://image.noelshack.com/fichiers/20 ... 4qfxa5.jpg

#19408
Scootydoo wrote:
Fri Aug 30, 2019 8:16 pm
souljah978 wrote:
Fri Aug 30, 2019 5:52 pm
How do you remove the dash plastic? need to access wires near the handlebar.
Two options really.
If you dont care about the cover or wont be needing it, you can crack it open with just about any blunt tool.

If you plan on salvaging the cover for reuse, you need to carefully take a razor or sharp knife and patiently run along the bottom edges of it where you can see the layer of glue. Take care not to go too deep(approx. 1/4 inch is ok) and once you are done, carefully lift up the cover and slice through any sections that might still be attached with glue.
I got it off with a hammer and a flat head without doing any major damage

By chabro343
Posts
#19457
That hallway looks like Camden, haha. I actually got myself the same exact model. Now I am looking to unlock it. So only way around it is to purchase those two items from amazon that you posted? After you install it, does it start smoothly? Thank you

By Mikepaiz
Posts
#19476
Self study-learning wire-intelligent wire-smart wire etc. usually single green sometimes white plugs into itself plug in when motor goes correct by using throttle power off unplug and there you go but must have hall sensors plugged in in order to work or just simply switch two of the three phase cables period To view images REGISTER or LOGIN for full access.

By burni720
Posts
#19673
Sorry if this question is redundant, I searched for it but found nothing.
Can someone tell me how to remove the red back lights to replace them? I only found one screw under the rubber surface. Is there another one somewhere or some other trick to open it?

By Meek one
Posts
#19692
I did it, you. A bird zero, new controller old throttle no lights or display just the motor.. It's so fast! Just wanted to thank you all for the help. I just read everything here over a few times and I'm new to all this, but happy I figured it all out! Maybe I'll post pictures cold my success

User avatar
By jamiesj410
Posts LikeBB LikeBB Avatar
#19713
burni720 wrote:
Thu Feb 13, 2020 12:00 pm
Sorry if this question is redundant, I searched for it but found nothing.
Can someone tell me how to remove the red back lights to replace them? I only found one screw under the rubber surface. Is there another one somewhere or some other trick to open it?
1 screw & they slide out

User avatar
By jamiesj410
Posts LikeBB LikeBB Avatar
#19714
Meek one wrote:
Fri Feb 14, 2020 2:30 pm
I did it, you. A bird zero, new controller old throttle no lights or display just the motor.. It's so fast! Just wanted to thank you all for the help. I just read everything here over a few times and I'm new to all this, but happy I figured it all out! Maybe I'll post pictures cold my success
U should see it with 2 battery’s & solid 10” tires !! I’m 240 pounds & it will climb any hill !

  • 1
  • 48
  • 49
  • 50
  • 51
  • 52

Bonjour j'ai effectuer le montage comme vous l ave[…]

Well mine started doing this also,same deal nothin[…]

hello i try this codee but not work i try all code[…]

NineBot Max - Attempt

I'm looking to convert my Lyft scooter pretty soon[…]