Page 2 of 5

Re: M365 Pro Clone Dashboard on OG M365 instructions

Posted: Tue May 21, 2019 2:50 am
by OliverVR
I have a regular 365 and it works.

Re: M365 Pro Clone Dashboard on OG M365 instructions

Posted: Mon May 27, 2019 5:32 am
by macmonka989
Hello.

I am also a "happy" owner of fake m365 pro display. I have a question for more experienced people. I installed this dashboard, I've uploaded DRV 1.5.5 but when I try to upload BLE or BMS my scooter loses connection with the m365_downg application. If I buy ST Link, according to this manual in Spanish, I will be able to correctly load BLE / BMS without soldering pins to the PCB (I do not have a soldering gun) ? Will it occur that I put pieces of wires and press firmly on the pins from the PCB?

PS. If I understand correctly in the first post the author wrote that there is probably no need for soldering, but I would rather be sure.

Thank you for the hints!

Re: M365 Pro Clone Dashboard on OG M365 instructions

Posted: Mon May 27, 2019 12:53 pm
by Whiteferrett
macmonka989 wrote:
Mon May 27, 2019 5:32 am
Hello.

I am also a "happy" owner of fake m365 pro display. I have a question for more experienced people. I installed this dashboard, I've uploaded DRV 1.5.5 but when I try to upload BLE or BMS my scooter loses connection with the m365_downg application. If I buy ST Link, according to this manual in Spanish, I will be able to correctly load BLE / BMS without soldering pins to the PCB (I do not have a soldering gun) ? Will it occur that I put pieces of wires and press firmly on the pins from the PCB?

PS. If I understand correctly in the first post the author wrote that there is probably no need for soldering, but I would rather be sure.

Thank you for the hints!
Yes you can manually hold the St link wires to the board to flash the Blu... It took me a couple of tries to get everything lined up correctly but once I got it correctly lined up everything went over just fine... Just make sure not to let go halfway thru the flashing... After that you can flash the bms with m365downg

Re: M365 Pro Clone Dashboard on OG M365 instructions

Posted: Mon May 27, 2019 2:24 pm
by macmonka989
Thank You for reply.

Did you have lost BT connection after installing this fake dashboard. DRV 1.5.5 I've uploaded earlier on the original dashboard from regular m365. Currently, BLE and BMS has values of -10201 as in the picture.

Regards !
Image

Re: M365 Pro Clone Dashboard on OG M365 instructions

Posted: Mon May 27, 2019 4:04 pm
by Whiteferrett
macmonka989 wrote:
Mon May 27, 2019 2:24 pm
Thank You for reply.

Did you have lost BT connection after installing this fake dashboard. DRV 1.5.5 I've uploaded earlier on the original dashboard from regular m365. Currently, BLE and BMS has values of -10201 as in the picture.

Regards !

https://ibb.co/jRvSc8z
So it shows all the correct values for the ble and bms now and I have verified flashing is working correctly by changing take off minimum speeds

Re: M365 Pro Clone Dashboard on OG M365 instructions

Posted: Tue May 28, 2019 2:51 am
by macmonka989
Last question :P Did you use male pins like in the picture, or did you cut the "plugs" on one side and put them on the PCB ?
Image

Re: M365 Pro Clone Dashboard on OG M365 instructions

Posted: Tue May 28, 2019 2:06 pm
by Whiteferrett
macmonka989 wrote:
Tue May 28, 2019 2:51 am
Last question :P Did you use male pins like in the picture, or did you cut the "plugs" on one side and put them on the PCB ?
Image
I literly just took the black plastic off the ends and held them on the dashboard... But if you put pins on thennthat should work better

Re: M365 Pro Clone Dashboard on OG M365 instructions

Posted: Wed May 29, 2019 1:23 am
by Mattr567
Can you still do custom firmware flashing using m365.botox.bz with the pro dashboard? I assume you have to use the newest DRV version for it to work properly.

Re: M365 Pro Clone Dashboard on OG M365 instructions

Posted: Tue Jun 04, 2019 1:47 am
by macmonka989
Whiteferrett wrote:
Tue May 28, 2019 2:06 pm
I literly just took the black plastic off the ends and held them on the dashboard... But if you put pins on thennthat should work better
Thank you again for your answers. Yesterday I received my st-link and according to the instructions, I loaded correct BLE into the dashboard (without soldering). Best wishes.

Re: M365 Pro Clone Dashboard on OG M365 instructions

Posted: Thu Jul 04, 2019 2:26 am
by Xpepino
Hello
I have M365 (non Pro)
I got dashboard clone from here:
https://www.aliexpress.com/item/32719659857.html
First i tried flash firmware before swap dashboard with modded firmware: (1.5.5)
http://xiaoscooter.site/ru/konstruktor-proshivok-pro
BUT: I tried download GONKAD365 1.5.5 (for non pro scooter) but without success (there is some error on page).
So i modify GONKAD - Change currents in Sport mode to lower and download this. (then it looks like GONKAD365)
I flash scooter with M365 DOWNG and replace dashboard .
Everything was working good, but maximum speed was 28km/h (not 35km - like i modded)
So i flashed this firmware again, and still maximum speed 28km/h :-/
Is there any way to put there higher speed ?
Thank you!