Page 23 of 28
Re: NineBot Max - Attempt
Posted: Wed Feb 19, 2020 4:32 pm
by BadAndy
I just finished flashing Spin dash but have not flashed the controller yet. Is it normal for the dash to not show proper battery level and not power off until the controller is properly flashed?
Re: NineBot Max - Attempt
Posted: Thu Feb 20, 2020 1:15 pm
by Sc00tr
BadAndy wrote: ↑Wed Feb 19, 2020 4:32 pm
I just finished flashing Spin dash but have not flashed the controller yet. Is it normal for the dash to not show proper battery level and not power off until the controller is properly flashed?
Yes, sometimes it will do that.
Re: NineBot Max - Attempt
Posted: Thu Feb 20, 2020 3:24 pm
by UnicycleSanta
BadAndy wrote: ↑Wed Feb 19, 2020 4:32 pm
I just finished flashing Spin dash but have not flashed the controller yet. Is it normal for the dash to not show proper battery level and not power off until the controller is properly flashed?
How are you planning to flash the controller? Do you have specific tutorial you are going to follow? Thats the part im getting stuck on.
Re: NineBot Max - Attempt
Posted: Thu Feb 20, 2020 11:38 pm
by BadAndy
I'm researching several posts and videos, most have been listed here or are linked to them. I had to order another st link as it took at zap from another projects capacitor. I should be back in business Sunday when it arrives. I will let you know how it goes.
https://www.scooterhacking.org/forum/vi ... f=26&t=213
Below is an older Ninebot controller how to video but should still be some what relevent.
https://www.scooterhacking.org/forum/vi ... f=26&t=213
Re: NineBot Max - Attempt
Posted: Thu Feb 20, 2020 11:49 pm
by BadAndy
Corrected Video how to link.
https://www.youtube.com/watch?v=hf_KrEb76ZY&t=1073s
You will have to hook to the newer controller correctly and use the correct dump files.
Re: NineBot Max - Attempt
Posted: Fri Feb 21, 2020 1:00 am
by UnicycleSanta
Ordered dash replacement from AliExpress. In the meantime I gotta figure out how to correctly wire the controller to the dash connector to avoid frying the dash and to have proper functionality. Also gotta figure out how to flash the BMS... I haven't seen too much on that one.
Re: NineBot Max - Attempt
Posted: Sat Feb 22, 2020 12:40 pm
by CapnBio
I have a max from spin, I'm waiting on a replacement cable, I already ordered an esc and dash, but I'm waiting on the cable to drive, when I got the dash and esc and connected it, I got an error 16 every time I turned it on, but I was able to connect to it no problem with Bluetooth and it said it was an accelerator problem. I'm waiting on the cable to come in so I can try again. I'll keep you guys posted.
Reason why I ordered a new esc and dash is because I fried them both by doing something stupid. No need to explain with pliers in my hands and keeping certain things connected
Re: NineBot Max - Attempt
Posted: Mon Feb 24, 2020 8:24 pm
by UnicycleSanta
Figured out how to flash the BMS, proper wiring, flashing the dash, and flashing the ESC. Now to do all of these things and report back. Once I get this running I will make an easy to follow comprehensive guide on how to convert Lyft scooters.
Re: NineBot Max - Attempt
Posted: Tue Feb 25, 2020 2:21 am
by landshark
Can the stock throttle be used by a generic motor controller?
I just want to know if I have to order a throttle as well. When I get it running, I promise to come back with some top speed GPS readings
Re: NineBot Max - Attempt
Posted: Tue Feb 25, 2020 7:15 pm
by Sc00tr
Stock throttle works with clone controllers.
landshark wrote: ↑Tue Feb 25, 2020 2:21 am
Can the stock throttle be used by a generic motor controller?
I just want to know if I have to order a throttle as well. When I get it running, I promise to come back with some top speed GPS readings
