An Electric Scooter Community on a Mission to Stamp out Transportation Mediocrity.

Discuss the Segway Ninebot ES and Ninebot Max Kick Scooter in this Forum. Topics include the Segway-Ninebot app, hardware, street riding, etc.
User avatar
By crackedhands
#19406
So a ”step down” refers to downgrading to a earlier version of the firmware?

I have found a broken Voi Scooter ES2 foldable. Some screws are missing and doesn’t beep when pushed. I’ve tried reading all the posts but is unsure if this scoot is possible to get going with a new motherboard? Then someone had used a ardunio and a downgrade. Where do I find that?
Image
Image
Image
By elodie78
#19412
Good morning all
I did the assembly of the arduino nano with bucks and the unlock code of mr spring
Everything worked perfectly, however overnight, I got an error message" 07E "
do you know what it is?
Thank you
By Risitas98
#19486
careragt35 wrote:
Sat Jan 11, 2020 5:24 am
I found Voi scooter
it looks like a modified version of the ninebot max g30d


Image

Image
Image
Image
Image


is this the same as the ninebot max g30 ?
Dear parisian baguette thief, this model is not hackable. Too hard and not beneficial for your business because the hardware is protected. You should left it on the street and call voi to repair the scooter.
User avatar
By crackedhands
#19499
Diagnostic Code

01E ~ High current protect

02E ~ Low voltage protect (battery or cHigh current protect)

03E ~ High voltage protect (controller problem)

04E ~ Locked motor protect

05E ~ Controller problem (MOS burned)

06E ~ Controller problem

07E ~ Motor problem

08E ~ Motor OT

09E ~ Throttle problem

10E ~ Brake problem (Usually broken brake lever)

11E ~ Signal transmission problem (controller problem)

12E ~ me, Signal transmission problem (controller problem)
By elodie78
#19514
crackedhands wrote:
Sat Feb 01, 2020 6:39 am
Diagnostic Code

01E ~ High current protect

02E ~ Low voltage protect (battery or cHigh current protect)

03E ~ High voltage protect (controller problem)

04E ~ Locked motor protect

05E ~ Controller problem (MOS burned)

06E ~ Controller problem

07E ~ Motor problem

08E ~ Motor OT

09E ~ Throttle problem

10E ~ Brake problem (Usually broken brake lever)

11E ~ Signal transmission problem (controller problem)

12E ~ me, Signal transmission problem (controller problem)
Thanks crackedhands :D
By Z3eraser
#19542
mayaku wrote:
Thu Jan 02, 2020 4:04 am
You are just F**** AWESOME!!!!!
Image

Image

Thanks a lot! :D :D :D :D
After I connected the Arduino with the Cables at the front for the gps can I cut the connection after the scooter works?
And how did you get power to the Arduino?
And what is the part left to the Arduino?

Thanks
User avatar
By mayaku
#19557
No, the Arduino needs to be connected all the time because it has to resend the command about every second.
And this tiny thing beside the Arduino is the power supply. A DC-DC buck converter to lover the voltage from the batteries' 42V to 5V ;)
Z3eraser wrote:
Wed Feb 05, 2020 10:16 am
mayaku wrote:
Thu Jan 02, 2020 4:04 am
You are just F**** AWESOME!!!!!
Image

Image

Thanks a lot! :D :D :D :D
After I connected the Arduino with the Cables at the front for the gps can I cut the connection after the scooter works?
And how did you get power to the Arduino?
And what is the part left to the Arduino?

Thanks
  • 1
  • 38
  • 39
  • 40
  • 41
  • 42
  • 44

As this was a rental version whos overstock was […]

Any one got any info on beryl bikes I seen a few[…]

LH/ TF-100 Style Display.

Hi I recently converted a Bird Zero to a personal […]

How do you operate dash without button? I have[…]