Page 4 of 19

Re: Lime Gen 3 Unlocked Software for 25kmh is now availiable

Posted: Mon Jan 27, 2020 12:41 pm
by M20001
Hello,

To find out if its possible to flash this Version of the lime gen 3 you have to disassemble one of the scooters and look inside. If the motor controller looks the same as the lime gen 3 we can try it. Would be interest in seeing whats inside this new Lime scooter. From where do you come? Where have you seen this scooter?

Re: Lime Gen 3 Unlocked Software for 25kmh is now availiable

Posted: Mon Jan 27, 2020 1:00 pm
by Pata27
Hey !

Re: Lime Gen 3 Unlocked Software for 25kmh is now availiable

Posted: Mon Jan 27, 2020 1:02 pm
by M20001
Hello,

Please if you can make detailed photos of the lime gen 3.1 so we can see whats inside, and how the scooter is built.

Re: Lime Gen 3 Unlocked Software for 25kmh is now availiable

Posted: Thu Feb 13, 2020 6:39 pm
by Ventomann
Hi there
I flashed the lime 3.0 successfully, it worked immediately after writing the hex file,
, headlights came on, the green light and the taillight.
Great, but another question how can you turn it off now (that the lamps go out until next time (how do you turn it on again)
after a short while he asks DONE? may I confirm that ???
MFG from Germany Berlin

Re: Lime Gen 3 Unlocked Software for 25kmh is now availiable

Posted: Fri Feb 14, 2020 3:50 pm
by M20001
Hello

Actually theres no way to disable the lights without flashing a locked firmware version to the scooter. The "Done" message should be disappear if you shake the scooter a little bit, it is in a normal case to ask the driver if he is done with renting.

Re: Lime Gen 3 Unlocked Software for 25kmh is now availiable

Posted: Sat Feb 15, 2020 3:01 am
by Caidyn
Ventomann wrote:
Thu Feb 13, 2020 6:39 pm
Hi there
I flashed the lime 3.0 successfully, it worked immediately after writing the hex file,
, headlights came on, the green light and the taillight.
Great, but another question how can you turn it off now (that the lamps go out until next time (how do you turn it on again)
after a short while he asks DONE? may I confirm that ???
MFG from Germany Berlin
Image
I wired up a simple toggle switch on the headlight wire. Cut off the black sheath and wire the switch up to interrupt either the black or the white wire

Re: Lime Gen 3 Unlocked Software for 25kmh is now availiable

Posted: Sat Feb 15, 2020 5:11 pm
by jonsmit
Hi, I've tried using the ST st-link V2 with stlink.git from texanne,

So finally, with stlink-gui & stink.git & all dependencies installed & the right connections between stlinkV2 and controller , I've managed to upload the .hex file.
Light is on, charger at poste, no green box.
Let's try it now.

Re: Lime Gen 3 Unlocked Software for 25kmh is now availiable

Posted: Mon Feb 17, 2020 12:46 am
by truted1
Hi there
I flashed the lime 3.0 successfully it worked after writing the hex file, but then stopped a short time after I disconnected the programming cables.
It only turns back on when I plug the charging cable in and take it out.

Re: Lime Gen 3 Unlocked Software for 25kmh is now availiable

Posted: Tue Feb 18, 2020 6:33 am
by jonsmit
jonsmit wrote:
Sat Feb 15, 2020 5:11 pm
Hi, I've tried using the ST st-link V2 with stlink.git from texanne,

So finally, with stlink-gui & stink.git & all dependencies installed & the right connections between stlinkV2 and controller , I've managed to upload the .hex file.
Light is on, charger at poste, no green box.
Let's try it now.
Well, without reconnecting the green box or the lcd, and pushing the scoot to start nothing much happened. Light went down shortly after.

Re: Lime Gen 3 Unlocked Software for 25kmh is now availiable

Posted: Tue Feb 18, 2020 7:44 am
by jonsmit
jonsmit wrote:
Tue Feb 18, 2020 6:33 am
jonsmit wrote:
Sat Feb 15, 2020 5:11 pm
Hi, I've tried using the ST st-link V2 with stlink.git from texanne,

So finally, with stlink-gui & stink.git & all dependencies installed & the right connections between stlinkV2 and controller , I've managed to upload the .hex file.
Light is on, charger at poste, no green box.
Let's try it now.
Well, without reconnecting the green box or the lcd, and pushing the scoot to start nothing much happened. Light went down shortly after.
Battery full after some serious tlc, reconnecting the green box:
All lights on, check.
Lcd green "asking are you done", km/h ok, check.
Bluetooth BLE ok asking for code through android phone, check.
No detection through eTrick app.
pushing up to 4-5 km/h into appartment no start...

disconnecting front light rear light on for some time, then scooter off.